This website was created with the help of AI and checked by us. Learn more

+49 2161 9173807office@oleopress.com
OleoPressInquiry

Oil press spare part diagnosis

Reading time about 4 minutes

As of: November 2026

Press cylinder, screw, press head or nozzle? How do I tell which spare part is really defective

When the oil press no longer runs smoothly – oil throughput drops, the machine vibrates or the press cake looks uneven – the question arises at once: is the problem with the screw, the press cylinder, the press head or the nozzle after all? This guide shows you how to narrow down the cause systematically without buying unnecessary parts.

1. How the four main components work together

Before we get to the diagnosis, a brief word on function: screw (press screw), press cylinder, press head and nozzle work as a system. The screw transports and compresses the seed in the press cylinder. The press head – a separate, replaceable component – closes off the pressure chamber and guides the compressed material specifically to the nozzle. The nozzle regulates the resistance at the outlet. If one of these four components is worn, it always affects the others as well.

2. Symptoms and their probable cause

The following table helps you narrow down the probable source of damage based on the symptoms observed:

SymptomProbable causePriority
Oil yield drops significantlyScrew wornHigh
Press cake is moist / greasyScrew, press head or nozzleHigh
Strong vibrations during operationScrew damaged / unbalancedImmediate
Oil escapes from the side of the press cylinderPress cylinder cracked / leakingHigh
Oil escapes at the press head transitionPress head worn or poorly seatedHigh
Uneven press cakePress cylinder or press head worn unevenlyMedium
Machine jams / clogsNozzle too narrow, press head or screw blockedImmediate
Loud metallic noiseScrew grinds against the press cylinder or press headImmediate
Excessive heat generationNozzle too narrow, press head incorrectly adjusted or screw overloadedMedium

3. Visual inspection: what you can see without tools

Checking the screw

Dismantle the screw and place it on a flat surface. Look out for:

  • Loss of material on the screw flights (recognisable by flattened areas)
  • Scoring or deep scratches along the screw channels
  • Visible asymmetry or bending
  • Discolouration from overheating (bluish-brown)

Checking the press cylinder

Hold the press cylinder up to the light and look through it from both sides:

  • Cracks or fractures in the wall
  • Uneven wear of the inner surface
  • Deposits or deformation in the drainage area (holes)

Checking the press head

The press head is a separate spare part and sits at the outlet of the press cylinder. Check:

  • Seating and fit: does the press head still sit firmly and flush?
  • Check the contact surfaces for runout and uneven wear
  • Inner surface for scoring, cracks or loss of material
  • Look for traces of oil at the press head transition – a sign of a leaking fit

Checking the nozzle

The nozzle is the easiest to replace and is often the first candidate when performance falls:

  • Check the diameter with a calliper – a worn seat enlarges the opening diameter
  • Uneven wear marks on the cone
  • Cracks or chipping

4. The diagnostic checklist: step by step

Go through these points in order before ordering spare parts:

  1. Check the nozzle first (quick to replace) – does that solve the problem?
  2. Check the press head for seating, fit and wear – traces of oil at the transition?
  3. Measure the screw for loss of material with a calliper. Rule of thumb: a deviation of more than 0.5 mm speaks in favour of replacement
  4. Check the press cylinder for cracks and ovality
  5. Carry out a test run with cleaned and calibrated seed
  6. Measure the oil yield and compare it with a reference value

5. Repair or replace? A decision aid

As a rough rule of thumb (not a manufacturer value): if the wear amounts to more than 10–15 % of the original diameter or cracks are visible, replacing is usually more economical than continuing to operate. A worn part always puts a load on the neighbouring component.

  • Nozzle: replace when worn – easy to change, often with a noticeable effect
  • Press head: replace in case of leakage at the transition, visible loss of material or poor seating
  • Screw: replace in case of visible loss of material or vibrations
  • Press cylinder: replace in case of cracks, severe ovality or leakage

6. Model-specific notes (IBG Monforts)

For owners of older IBG Monforts presses (CA59, D85, DD85, S120F, K series): since the insolvency proceedings of IBG Monforts (preliminary proceedings from March 2023), parts from IBG Monforts are, to our knowledge, no longer available from IBG. OleoPress offers Monforts spare parts. They are similar to the parts of the Oleo P machines, but not interchangeable. You will find more on this, and advice, on the comparison page; we also advise you in person.

Conclusion

A systematic visual inspection saves time and money. In most cases the symptoms make it clear whether the screw, press cylinder, press head or nozzle is causing the problem. Start with the component that is easiest to replace – the nozzle – and work your way up to the more laborious screw. Do not forget the press head: as a separate spare part it is often overlooked, but it is a frequent cause of leakage and pressure loss.

Inquiry list

Nothing saved yet.

Inquiry by emailTo the contact page