How does a screw press work? Cold pressing of oil explained
The screw press is the heart of every cold-press plant. From the outside it looks like a sturdy piece of industrial engineering; inside, screw, cylinder and nozzle work together to obtain oil purely mechanically, without chemical solvents.
1. The basic principle of the screw press
A screw press – also called an expeller or screw extruder – works on a simple principle: mechanical pressure through rotating displacement. A spiral screw turns inside a fixed, perforated cylinder (strainer cage). The oil-bearing material – seeds, kernels or nuts – is conveyed by the screw movement towards a narrowing nozzle. Pressure builds up continuously until the oil is squeezed out of the cell tissue and runs off through the perforations of the cylinder.
The process works continuously. Unlike the historic batch press, where one portion at a time had to be pressed and removed, the screw press runs through: seed is fed in at the top, oil runs off at the side, and the press cake leaves the machine at the end of the cylinder.
Schematic sequence
- Feed hopper: load the raw material
- Press screw: conveying and pressure build-up
- Press cylinder: oil escapes
- Nozzle: pressure control
- Press cake: solid residue
2. The three core components in detail
Every screw press consists essentially of three main components. Their condition determines yield, oil quality and the service life of the plant.
The press screw: the heart of the machine
The press screw – often also called the “worm” – is the main moving part of the oil press. It carries spiral flights and is made of hardened steel.
The quality of the screw is decisive for pressing performance. If it wears down, the pressure built up falls and the yield declines. A worn screw is therefore one of the most common maintenance issues and should be recognised early.
The press cylinder: separating oil and solids
The press cylinder encloses the screw like a close-fitting tube and separates oil and solids. It has fine bores. When the material is compressed, the liquid oil passes outwards through these openings; the solid part, the press cake, cannot get through and is conveyed to the nozzle.
The gap between screw and cylinder matters: if it is too narrow, friction creates unwanted heat; if it is too wide, the pressure collapses.
The nozzle: regulator of the pressure
At the end of the press cylinder sit the nozzle and the press head. The nozzle acts like an adjustable constriction: the further it is closed, the higher the back pressure in the cylinder. Higher pressure generally means a better oil yield, but also more frictional heat. The nozzle setting is therefore the most important parameter for balancing yield and quality.
3. The pressing process step by step
The pressing process runs in several phases that merge smoothly into one another:
- Filling and intake. The seed falls from the hopper into the intake area of the screw. Here the screw still has a wide pitch and conveys the material quickly forward. There is hardly any compression yet.
- Compression zone. As it nears the nozzle, the flight depth of the screw decreases. The volume shrinks, the pressure rises. The cells of the seed are broken open, the oil is released and begins to flow through the openings of the press cylinder.
- Maximum pressing pressure at the nozzle. Immediately before the nozzle the pressure reaches its maximum. At the same time the dry, compact material rubs more strongly against the metal walls. This is where most of the frictional heat is generated. In cold pressing it is kept low by adapted settings.
- Press cake discharge. What leaves the nozzle is the press cake, a solid, dry strand of the de-oiled plant material. How much residual oil it contains depends on the seed and setting. An even, firm press cake indicates a suitable setting.
- Oil collection and pre-filtering. The oil that has run off is collected in a tray under the press. It is still cloudy and contains fine suspended matter. This crude oil can be bottled as naturally cloudy oil or processed further via a filter press to obtain a clear end product.
4. The press cake and its use
When pressing oil, the press cake is produced alongside the oil. Many businesses see it as waste, yet it can be put to use.
What is press cake made of?
Press cake is the solid material left over after pressing. It contains mainly protein, dietary fibre and residual oil. The composition depends strongly on the seed.
Possible uses
- Animal feed: The most common use is animal feed in agriculture. Which press cakes are suitable for this and in what quantity, please clarify in advance with your veterinarian or the competent authority.
- Further processing: for example milling into flour or use as an additive.
- Energy: Press cake can, under certain circumstances, be used as fuel.
- Fertiliser: Press cake can be used as organic fertiliser in gardening and arable farming.
Common mistakes
- Press cake is thrown away although it could be used.
How using it affects the economics is described in the article Economics of cold pressing.
5. What does “cold-pressed” mean?
“Cold-pressed” describes a process in which the oil is obtained purely mechanically, without chemical solvents. The term is not a temperature specification: pressing always generates some heat through friction, which depends on the seed, speed and nozzle setting.
“Cold-pressed does not mean that no heat is generated at all – but that the oil is obtained purely mechanically, without chemical solvents.”
By comparison: in industrial hot extraction, the seed is heated before pressing to increase the yield. Solvents are then often used to dissolve out the remaining oil. The oil is then usually refined. Cold-pressed oils, by contrast, generally keep the typical taste of the seed.
6. Screw press and other processes
Oil pressing processes compared
| Process | Principle | Cold pressing | Operation | Use |
|---|---|---|---|---|
| Screw press (our process) | Continuous pressure from a rotating screw in the press cylinder. Seed is conveyed, compressed and oil is separated through perforations. | Possible | Continuous | Farm to industry |
| Hydraulic batch press | A hydraulic ram presses the seed one portion at a time. After each pressing cycle the press cake has to be removed. | Possible | Batch | Craft, laboratory |
| Hot extraction with solvent | Seed is heated and then extracted with solvents. The crude oil then has to be refined at great expense. | Not possible | Continuous | Industry |
| Centrifugal extraction | Centrifugal force separates oil from pulp or paste. Suitable for olives and avocados, where the oil is in the pulp. | Possible | Continuous | Olives, avocado |
The information is simplified guide values and depends on the seed and machine setting.
7. Wear, maintenance and spare parts
The mechanical stress in a screw press is considerable. Press screw, cylinder, press head and nozzle are in continuous use under high pressure in contact with hard, abrasive material.
When should you order spare parts?
Rule of thumb: with intensive use (several hours a day), press screws and cylinders should be checked about every 1–2 years and replaced if necessary. With occasional use, the wear part lasts considerably longer. What matters is regularly observing the pressing performance, not a fixed time interval.
Recognising typical wear patterns
1. Press screw (worm)
The most common wear part – direct contact with abrasive material.
- Symptoms: Falling oil yield with the same amount of seed. Press cake becomes damp and greasy.
- Cause: The screw flights lose depth and sharpness. Less pressure is built up, and the oil partly stays in the press cake.
- Action: Check the press screw and replace it if there is measurable wear.
2. Press cylinder
Perforated outer tube – bores and inner wall wear.
- Symptoms: Rising heat build-up despite the same setting. Cloudy oil with more fine particles. Pressure loss in the cylinder.
- Cause: The bores widen through wear and solid particles get into the oil. Or: the bores become clogged with press cake remnants and increase friction.
- Action: Clean the cylinder after operation and check for blockage or widening. Replace it if it deviates.
3. Nozzle
Pressure regulator at the outlet – the contact surface with the press cake wears.
- Symptoms: With the same setting, the press cake varies in moisture and density. The oil yield fluctuates.
- Cause: The contact surface of the nozzle is worn away unevenly by friction.
- Action: Check the nozzle opening for evenness. If discharge is irregular, clean the nozzle first.
Tip: Keep a simple operating-hours logbook. This way you recognise drops in performance early. The spare part diagnosis offers step-by-step help.
8. Which seeds can be pressed?
One strength of the screw press is its versatility. With a suitable setting of speed and nozzle opening, a large variety of oil-bearing seeds can be processed. You can find an overview with the matching screw under Seeds.
Classic oil seeds such as rapeseed, sunflower, linseed and hemp are among the most frequently pressed raw materials. They have a high oil content and flow well through the machine.
Nuts and kernels such as walnut, hazelnut, almond, pumpkin seed and sesame often need somewhat less pressure and special care because their aroma is delicate.
Speciality oils such as black cumin, milk thistle, grape seed, argan or rosehip are gaining in importance. Many of them are offered cold-pressed because seed, temperature and process influence the taste.
Cereal germs such as wheat or maize germ can also be pressed, but usually with a low yield. This limits economic use to niche products.
Practical tip: With seeds that have a high proportion of hull, such as sunflower or pumpkin, hulling before pressing can make sense. It can reduce wear on the screw.
9. Conclusion
The screw press combines continuity and flexibility in one compact machine. Whether for the farm shop, direct marketing or the small oil mill: it delivers oil from a wide range of raw materials. Press screw, cylinder and nozzle are the parts you should pay particular attention to in operation.
Spare parts for your oil press
You can find press screws, press cylinders and nozzles in our spare parts overview.
Further reading: Seed list (58 seeds) · Oil mill yield calculator · Our oil presses · Spare parts for oil presses