Spare parts oil presses

Wear Parts & Accessories

Original quality from Kambas Oleopress

high quality Spare and wear parts for screw oil presses – Made to precise technical specifications. for our OleoPress oil presses, IBG Monforts Oil Presses the insolvent IBG Monforts Oekotec GmbH & Co. KG. and compatible with common models from other manufacturers. Secure the longevity and performance of your oil press.

#ATFP_CLOSE_Translate_Span#

Spare parts for large oil presses

The following overview shows a selection of available spare parts for Screw Oil Presses. A complete overview of which parts are compatible with which machine models can be found on our compatibility page.

#ATFP_CLOSE_Translate_Span#

Spare parts for small oil presses

For compact screw oil presses, we offer a separate range of wearing parts. The smaller sizes have specific geometries that are not compatible with the parts for large machines.

#ATFP_CLOSE_Translate_Span#

#ATFP_CLOSE_Translate_Span#

Why Kambas OleoPress Replacement Parts for Your Oil Press

A screw oil press is a machine that works under considerable mechanical stress. The press screw (spindle) Constantly rotates against the pressed material and transmits forces that generate several tons of surface pressure. The press cylinder Withstand this pressure permanently – layer by layer, ton for ton pressed seed.

These components wear out over time. This is not a defect, but due to the design: wear parts are deliberately designed to wear out and remain replaceable – to protect more expensive machine components such as transmission and engine. However, who inferior spare parts installed, risks more than just bad press results: in the worst case, incorrectly tolerated parts can damage the pressing cylinder, overload the gearbox or impair the oil quality through metal abrasion.

Kambas OleoPress manufactures its spare parts according to their own precise specifications – with the same materials and tolerances that are also installed in our own machines. This guarantees a perfect fit, smooth running and maximum service life.

#ATFP_CLOSE_Translate_Span#

When do spare parts need to be replaced?

Many operators wait too long to change spare parts – often until a clearly noticeable loss of performance occurs. There are early warning signals that indicate worn components:

Signs of a worn press spindle

• The Oil yield decreases Measurable, although the same seed and the same settings are used.
• The Press cake contains significantly more residual oil as usual – recognizable by the fatter, darker appearance.
• The machine is running more restless or vibrates more than in new condition.
• Elevated motor temperature or more frequently triggered the thermal fuse.

Signs of a worn press cylinder

• The Pressed oil is cloudy As usual – an indication that the gap dimensions of the strainer basket have become too wide and press cake particles get into the oil.
• Uneven oil flow from the strainers.
• visible called or deformations on the inner wall of the cylinder.

Signs of an incorrectly set or worn nozzle

• The Press cake is too soft or does not break cleanly – indicates too low back pressure.
• The Pressing temperature rises too much ON – The nozzle opening may be too small or clogged.
• Irregular pellet shape Or crumbly cake after the nozzle.

Rule of thumb for life: With regular operation (several hours a day), the pressing spindle should be checked every 500–1,000 hours of operation. The press cylinder usually lasts longer, but should be checked for wear at least once per season. The exact intervals depend on the seed, the grain size and the operating temperature.

#ATFP_CLOSE_Translate_Span#

Which spare part for which seed?

Not every oil press and not every seed places the same demands on the wearing parts. An essential factor is the Hardness and moisture of the pressed material: Hard, dry seeds such as rapeseed or sunflower seeds put more strain on the snail than soft, moist seeds such as flax seeds or walnuts.

Seeds	Recommended spindle	Special feature
Rape	R8	Highly oily, hard grain – high wear pressure
sunflower	R8	Enhance Shells Abrasion – Check the spindle regularly
Linseed	R11	Soft, slimy pressed material – R11 prevents clogging
pumpkin seeds	R11	High volume of oil, soft structure – lower pressure required
walnuts	R11	Wet cores – low temperature important
Mustard	R8	Small grain, hard pressed material – good sealing required
hemp seeds	R11	Soft seeds, heat-sensitive ingredients

If you are unsure which spindle is best for your seed, we will be happy to advise you directly – by phone or via our contact form.

#ATFP_CLOSE_Translate_Span#

Compatibility: Which machines are supported?

Our spare parts are primarily for the Oleopress machine series (Oleo P 8, P 20, P 40). In addition, many parts are compatible with oil presses from other manufacturers whose geometries are similar or identical in construction.

Known compatible models include, among other things, machines from Oeltech (e.g. FX20 – there is also a special one for this expansion set) as well as selected models of IBG Monforts Oekotec. The exact compatibilities are in our Compatibility Table listed.

If you own a machine that is not listed in the table, please send us the Type designation and dimensions the parts to be replaced. We then check whether one of our spare parts fits or whether we can offer a special production.

#ATFP_CLOSE_Translate_Span#

Extension set for Oeltech FX20

For operators of Oeltech FX20 we offer a specially developed expansion set that allows the use of Oleopress spare parts in this machine. The set contains all the necessary adapters and parts to allow for easy change without complex conversions – ideal for anyone who wants to benefit from cheap original parts and quicker availability.

#ATFP_CLOSE_Translate_Span#

Frequently asked questions about oil press spare parts

How do I find out which part I need?

The easiest about our Compatibility Table: All machine models and the matching parts are listed there. Alternatively, you can send us the type designation of your machine and – if possible – the dimensions of the part to be replaced. We will then help you directly.

What is the difference between press spindle R8 and R11?

Both spindles have the same external geometry and can be used in the same machines. The difference lies in the slug slope and geometry: the R8 is designed for hard seed (rapeseed, sunflower, mustard) and generates higher pressing pressure. The R11 Optimized for soft seed (Linse, Pumpkin, Walnut) and works with less resistance, preventing clogging and keeping the oil temperature low.

How often should the press spindle and press cylinder be changed?

This depends heavily on the press volume, the seed and the operating temperature. As a guideline, the following applies: at regular operation (several hours daily) the pressing spindle should be checked every 500-1,000 hours of operation and replaced if necessary. It is best to check the pressing cylinder once per season for wear, grooves or changed gap dimensions.

Are the parts also suitable for older IBG Monforts oil presses?

Our parts are compatible for selected models from the former IBG Monforts Oekotec GmbH & Co. KG. You can see which models are supported in the Compatibility Table. You can find more information about the old IBG Monforts oil press on our Overview page.

Can I also pick up spare parts from your site?

Yes, after prior agreement, collection from our warehouse in Mönchengladbach is possible. Contact us in advance by phone or e-mail so that we can have the desired parts ready for you.

How long does the delivery take?

Storage parts are usually shipped within 1-2 working days. In the case of special production or parts that are not in stock, we will discuss the delivery time with you in advance. We strive to keep your machine downtime as short as possible.

#ATFP_CLOSE_Translate_Span#

Kambas OleoPress – your specialist for oil press spare parts

Kambas OleoPress is a company specializing in oil presses and accessories, based in Monchengladbach. We develop and manufacture our spare parts according to our own specifications – with the claim that every part is as durable and powerful as the original. Our customers range from Hobbyölmüller with a small table press to the contract press company with several industrial machines.

What distinguishes us: Short delivery times, personal advice and fair prices. We know that a standing oil press costs money – and we do everything we can to keep downtime as short as possible for you. Talk to us.